This Tail Gear Case H2 is designed very light weight and solid to allow entire Tail Rudder System to operate up 20,000 RPM without vibration
|
| The Tail Rudder Servo Mount H2 is designed very light weight and strong to mount the Tail Rudder Servo securely onto the tail boom. It's also to allow to mechanically adjust servo position to achive maximum tail control performance without exceeding servo travel limit. It is designed to improve tail control performance on Hornet II helicopters. |
|
| Reg. Price: | $59.99
|
| Sale Price: | $44.00
|
| Save: | $15.99 |
| Items Remaining: | 2 |
 |
|
|
|  |
 |
Usage: Hornet FP, CP, Hornet II |
|
Description: Compatible with the stock plastic bell crank!
|
|
|
|
Description: Not compatible with stock plastic bell crank!
|
MicroHeli Upgrades for your Ms Hornet
|
| Reg. Price: | $79.99
|
| Sale Price: | $59.00
|
| Save: | $20.99 |
| Items Remaining: | out of stock |
|
|
|
| |
|
For MS Hornet II
Stainless Steel Hollow Main Mast
by Walt Ferar
3mm O/D hollow, 2.5mm I/D - 2.9 grams
Lighter and stronger than stock
|
Ball belcranks by Walt for Hornet 2
|
Custom Machined MS Hornet
Tail Rotor Shaft Spacer W/Washer
Replaces the orange plastic spacer
|
Features; Minimal wind up - No center bearing to wear out - Higher gyro gain possible - Simplicity in installation - No power loss from center bearings - No whip - Precision titanium ends. It is a direct retrofit and requires no other parts to replace the stock shaft.
>>> Lifetime Guarantee <<<
|
Walts "W" Carbon Fiber Tail Blades are made for FP and CP Hornet helicopters to improve tail controls and tail performance.Weight: 0.41 grams Usage: Hornet...
|
For collective pitch MS rotor head
|
For MS Hornet white or black main gears
No more stock gear pins slipping out
|
For the dual bb MS Hornet slider
Stainless Steel Sleeve Upgrade For The
E193 Tail Pitch Slider
No More Wear From The Stock Brass Inner Sleeve
|
MS Composit Hornet Bell Hiller Mixer Set
For Hornet CP, CPX, The Hornet II
|
Complete With 2 ea Titanium Bolts - 2 ea Washers - 2 ea Nylock Nuts, And Complete Installation Instructions
|
Duzi Upgrades for your Ms Hornet
This is the new version with metal balls
|
| Reg. Price: | $50.75
|
| Sale Price: | $39.90
|
| Save: | $10.85 |
| Items Remaining: | out of stock |
|
 |
|
| |
Duzi Upgrades for your Ms Hornet
|
| Reg. Price: | $157.00
|
| Sale Price: | $110.00
|
| Save: | $47.00 |
| Items Remaining: | out of stock |
|
|
|
| |
Upgrades for your Ms Hornet 2
This is the new version with metal balls
|
|
|
|
| order.nr.: MT4000.5 |
| Blade Grip Slave Lever - 2pcs |
|
| order.nr.: MT4000.7 |
| Center Shaft. |
|
| order.nr.: MT4000.9 |
| Main Shaft. |
|
|
|
|
| Reg. Price: | $99.00
|
| Sale Price: | $68.00
|
| Save: | $31.00 |
| Items Remaining: | 1 |
|
|
|
| |
| order.nr.: MT4001MX |
The same Bell-Hiller system as MT4001, including a high precision bearing links.
This set works only with metal head MT4000. |
|
| Reg. Price: | $85.49
|
| Sale Price: | $71.99
|
| Save: | $13.50 |
| Items Remaining: | out of stock |
|
| |
|
| |
Duzi Upgrades for your Ms Hornet
|
This alu-upgrade is very light and balanced with slightly adjusted geometry for better responsiveness when combined with the bell-hiller upgrade part MT4001. Securing of the fly bar in the horn is similar as in the original part, however, it does not bend the wire and hence does not change characteristics of the paddles.
|
| order.nr.: MT4011.4 |
| Conical Tail Gear for MT4011. |
|
| order.nr.: MT401x.2 |
| Pinion 12T/3,15mm. |
|
|
|
|
|
|
Duzi Upgrades for your Ms Hornet
|
Duzi Upgrades for your Ms Hornet
price is for complete set
|
| Reg. Price: | $45.99
|
| Sale Price: | $28.90
|
| Save: | $17.09 |
| Items Remaining: | 1 |
|
|
|
| |
|
| Indestructible, very light-weight and precise grips enable extremely smooth (ball bearings) movements of the tail pitch slider |
|
|
| Strong yet lightweight clamps for the tail servo. It makes the adjustment of the neutral position of tail blades extremely easy and CA-free. This upgrade is designed for HS-50 servos and a pair of clamps is required for mounting. |
|
Made from lightweight aluminum,
no glue is used in tail assembly
|
|
| Strong yet lightweight clamp enables quick and comfortable assembly/disassembly of the tail gearbox. It provides also a mounting base for the vertical fin. Everything is CA-free. |
|
This holder serves two purposes. It is a mounting base for the horizontal fin and for the tail boom support rods.
|
Fully CNC ball bearing tail grips. Drop in replacement for the tail rotor hub blade grips, exceptionally smooth. 2 bearings in each grip. Will come in anodized blue alum. shown here in natural
|
Fully CNC tail tail clamp,(Anodized Blue) no more glueing in place just bolt it on and fly, no chance of coming unglued in flight.
CF fin included in the kit.
|
Fully CNC tail rotor servo / vertical fin mount. (Anodized Blue)No more glueing in place, just bolt it on and fly. No chance of it coming unglued in flight.
Fits HS-50 servo. CF fin included in kit.
|
Heliup CNC Aluminum/CF Hornet II Frame
Bolt on servo mounts ( No more servo tape )
|
These are for guys who want to use Fut 3108's or HS 50's
that the Duzi doesnt fit
|
This plate gives you great mounting for gyro in the best location for solid tail
|
For The E230 One-Way Clutch
|
Upgrade your stock SwashPlate
Takes out the slop and makes for smooth control --This one a Must Have--
|
Upgrades for your Ms Hornet
|
Upgrades for your Ms Hornet
|
Upgrades for your Ms Hornet
|
Upgrades for your Ms Hornet
|
Upgrades for your Ms Hornet
|
|
